PhysicsDrillFree guides

College physics · Instant answer checks

Inclined plane problems with friction

Almost every inclined plane problem with friction comes down to one question: does the block move? Answer that first, because it decides which friction formula you’re allowed to use. If the block holds still, friction is only as big as it needs to be. If it slides, friction is μₖN. Everything below uses g = 9.8 m/s², and θ is the ramp’s angle above horizontal.

Start with the stick-or-slip test

For a block initially at rest on a fixed ramp, with only gravity, the normal force and friction acting, run these three steps. If it is already sliding, use kinetic friction instead. If a rope or another push acts, include it in the force balance.

  1. Find the two forces along the ramp. Gravity pulls the block downhill with mg sin θ. The most static friction can give is μₛN, which is μₛ mg cos θ if nothing else presses on the ramp.
  2. Compare them. Mass and g cancel, so for a block alone on a ramp the test is just tan θ against μₛ.
  3. Pick your branch. If tan θ ≤ μₛ, the block stays and f = mg sin θ. If tan θ > μₛ, it slips and f = μₖN.

This is why f = μN causes so much trouble. For a block at rest, μₛN is a ceiling, not the actual force. The real friction force matches whatever it has to, up to that ceiling.

Inclined plane friction formulas

Each row assumes a block on a fixed ramp with no other forces unless the row says so. Take downhill as positive for a: a negative result means acceleration uphill, not necessarily motion uphill.

Which formula goes with which situation
SituationFormulaFriction points
Normal forceN = mg cos θNot friction, but you need it first
At restf = mg sin θ, as long as f ≤ μₛNUphill
About to slipθ = tan⁻¹(μₛ)Uphill, at its maximum
Sliding downa = g(sin θ − μₖ cos θ)Uphill
Sliding upa = g(sin θ + μₖ cos θ), slowing downDownhill
Constant speed, sliding downμₖ = tan θUphill
Pushed up at constant speed, force along rampF = mg(sin θ + μₖ cos θ)Downhill

Friction points against the sliding, or against the way the block is trying to slide. It doesn’t automatically point uphill, which is the mistake behind a lot of lost points.

Draw it with tilted axes

Choose x downhill along the ramp and y perpendicular into it. For a block with only weight, normal force and friction, only the weight needs splitting. If the arrows themselves are the sticking point, go through the free body diagram practice first.

Force diagram for a block on a rampA block sits on a ramp tilted at angle theta. Weight mg points straight down. The normal force N points away from the ramp at a right angle. Friction f points along the ramp, uphill, for a block sliding down or about to. Dashed lines split the weight into mg sin theta along the ramp and mg cos theta into the ramp.θmgNfmg sin θmg cos θ
Friction is drawn uphill because this block is sliding, or trying to slide, downhill. Dashed arrows are the two parts of mg. They replace mg in your equations; they aren't extra forces.

The angle between mg and the line perpendicular to the ramp equals θ, so sin goes with the along-the-ramp part and cos with the into-the-ramp part. A quick check: at θ = 0, the ramp is flat, and all of mg should press into it. cos 0° = 1, so that works.

Try it on a live ramp

Four worked examples, easiest to hardest

Example 1: the block that doesn’t move

A 10 kg block sits on a 20° ramp with μₛ = 0.50 and μₖ = 0.35. Find the friction force.

  1. Test. tan 20° = 0.364, which is below 0.50, so the block stays.
  2. Forces. N = (10)(9.8)(cos 20°) = 92.1 N, so the ceiling is μₛN = 46.0 N.
  3. Friction. Balance along the ramp: f = mg sin θ = (10)(9.8)(sin 20°) = 33.5 N uphill.

The answer is 33.5 N, not 46.0 N. μₖ was a distractor, since nothing is sliding.

Example 2: the block that slides

A 5.0 kg block on a 25° ramp has μₛ = 0.40 and μₖ = 0.30. It’s released from rest. Find its acceleration.

  1. Test. tan 25° = 0.466, above 0.40, so it slips.
  2. Forces. Downhill pull: mg sin θ = 20.7 N. N = 44.4 N, so f = μₖN = (0.30)(44.4) = 13.3 N uphill.
  3. Newton’s second law. a = (20.7 − 13.3) / 5.0 = 1.5 m/s² down the ramp.

The shortcut agrees: g(sin 25° − 0.30 cos 25°) = 1.5 m/s². The block needed μₛ only to prove it moves.

Example 3: up the ramp, then back down

A 2.0 kg block is sent up a 30° ramp at 6.0 m/s, with μₖ = 0.25 and μₛ = 0.35. How far up does it go, and how fast is it when it gets back?

  1. Going up. Friction points downhill, joining gravity: a = 9.8(sin 30° + 0.25 cos 30°) = 7.0 m/s², slowing it down.
  2. Distance. d = v² / (2a) = 36 / 14.0 = 2.6 m.
  3. At the top. The block stops, so run the test again: tan 30° = 0.58, above 0.35, so it slides back.
  4. Coming down. Friction flips to uphill: a = 9.8(sin 30° − 0.25 cos 30°) = 2.8 m/s².
  5. Return speed. v = √(2ad) = √(2 × 2.8 × 2.6) = 3.8 m/s.

The acceleration changes at the top because friction changes direction. The block comes back slower than it left because friction removed energy on both trips.

Example 4: a ramp with a pulley

A 4.0 kg block on a 30° ramp is tied by a light rope over a massless, frictionless pulley to a hanging 5.0 kg mass. μₛ = 0.30 and μₖ = 0.20. The taut rope does not stretch and runs parallel to the ramp. Starting from rest, find the acceleration and rope tension.

  1. Test. The hanging weight is 49 N. The ramp block’s downhill pull is 19.6 N. That leaves 29.4 N trying to drag the block uphill, and μₛN is only 10.2 N. So it moves, block going uphill.
  2. Friction. The block moves uphill, so friction points downhill: f = μₖN = (0.20)(33.9) = 6.8 N.
  3. Hanging mass. 49 − T = 5.0a.
  4. Ramp block. T − 19.6 − 6.8 = 4.0a.
  5. Add the equations. T cancels: 22.6 = 9.0a, so a = 2.51 m/s².
  6. Tension. T = 5.0(9.8 − 2.51) = 36.4 N.

Check it with the other equation: 19.6 + 6.8 + (4.0)(2.51) = 36.4 N. Also notice that T is less than 49 N, which it has to be for the hanging mass to accelerate down.

Want more problems like these, sorted by chapter?

Try 3 days free

Mistakes that cost the most points

Common mistakes and how to catch them
MistakeQuick fix
Using f = μₛN for a block at restThat’s only the maximum. Balance the forces to find the real f.
Writing N = mg on a rampWrite the force equation perpendicular to the ramp and solve for N.
Swapping sin and cosPicture θ = 0. The along-the-ramp pull must go to zero, and sin 0° = 0.
Always drawing friction uphillAsk which way the block slides or wants to slide, then point friction the other way.
Keeping the same a after the block turns aroundFriction flips when the motion does, so the acceleration changes too.
Getting a negative a and calling it a backward slideFriction can’t reverse a block on its own. For a lone block released from rest on a fixed ramp with μₖ ≤ μₛ, a negative result from the downhill sliding formula means static friction can hold it. For a block already sliding down, negative a means it slows down.

Practice problems with instant checks

Type a number without units and press Check answer. Rounding differences won’t count against you. Wrong answers tell you which mistake you probably made, when we can spot it. Use g = 9.8 m/s² throughout. In all pulley problems, assume a taut, massless, inextensible rope parallel to the ramp, and a fixed, massless, frictionless pulley.

1. An 8.0 kg crate sits on a 15° ramp with μₛ = 0.40. It starts from rest. What happens?
Show solution 1
  1. Compare tan θ with μₛ: tan 15° = 0.268.
  2. 0.268 is less than 0.40, so the crate stays put.

2. Same crate: 8.0 kg, 15°, μₛ = 0.40, at rest. How big is the friction force on it?

Show solution 2
  1. The crate is at rest, so the forces along the slope balance: f = mg sin θ.
  2. f = (8.0)(9.8)(sin 15°) = 20.3 N, pointing uphill.
  3. The maximum available is μₛN = 30.3 N, so this is well within the limit.

3. A 3.0 kg block sits on a 35° ramp with μₛ = 0.45 and μₖ = 0.30. Once released it slides. What is its acceleration?

Show solution 3
  1. Check: tan 35° = 0.70, above μₛ = 0.45, so it does slide.
  2. a = g(sin θ − μₖ cos θ) = 9.8(0.574 − 0.30 × 0.819).
  3. a = 3.2 m/s² down the slope. The 3.0 kg was never needed.

4. A book slides down a ramp tilted at 18° at constant speed. What is μₖ?

Show solution 4
  1. Constant speed means zero acceleration, so f = mg sin θ.
  2. μₖ mg cos θ = mg sin θ, which gives μₖ = tan θ.
  3. μₖ = tan 18° = 0.32.

5. A block is sliding up a 25° ramp at 5.0 m/s when it’s let go, with μₖ = 0.20. How far up the ramp does it go before it stops?

Show solution 5
  1. Moving uphill, gravity’s pull and friction both point downhill: a = g(sin θ + μₖ cos θ).
  2. a = 9.8(0.423 + 0.20 × 0.906) = 5.92 m/s².
  3. d = v² / (2a) = (5.0)² / (2 × 5.92) = 2.1 m.
6. A 12 kg box on a 30° ramp stays at rest while a rope pulls it up the slope with 80 N. Which way does static friction on the box point?
Show solution 6
  1. The downhill part of the weight is mg sin θ = (12)(9.8)(0.50) = 58.8 N.
  2. The rope pulls up with 80 N, so without friction the box would slip uphill.
  3. Static friction points down the slope, with size 80 − 58.8 = 21.2 N.

7. A 20 kg crate rests on a 20° ramp with μₛ = 0.55. What is the limiting applied force, parallel to the ramp, just before it starts moving uphill?

Show solution 7
  1. About to move uphill, static friction is at its maximum and points downhill.
  2. N = mg cos θ = (20)(9.8)(cos 20°) = 184 N, so μₛN = 101 N.
  3. F = mg sin θ + μₛN = 67.0 + 101 = 168 N. A force just above this limit starts uphill motion.

8. A 6.0 kg block sits on a 30° ramp. A 40 N horizontal force pushes it toward the ramp. What is the normal force?

Show solution 8
  1. Into the ramp, the weight gives mg cos θ = (6.0)(9.8)(cos 30°) = 50.9 N.
  2. The horizontal push adds F sin θ = (40)(0.50) = 20 N.
  3. Nothing accelerates perpendicular to the ramp, so N = 50.9 + 20 = 70.9 N, or about 71 N.

9. A 5.0 kg block on a 30° ramp is tied over a pulley to a hanging 6.0 kg mass. μₖ = 0.25 and the system is moving, with the hanging mass going down. What is the acceleration?

Show solution 9
  1. Hanging weight pulls forward: (6.0)(9.8) = 58.8 N.
  2. Resisting: mg sin θ = 24.5 N, and friction μₖN = (0.25)(42.4) = 10.6 N.
  3. a = (58.8 − 24.5 − 10.6) / (5.0 + 6.0) = 2.2 m/s².

10. A 10 kg block sits on a 25° ramp with μₛ = 0.40, tied over a pulley to a hanging mass. What is the largest hanging mass that still lets the block stay at rest?

Show solution 10
  1. At the limit the block is about to slip uphill, so static friction is at its maximum and points downhill.
  2. The hanging weight balances both: Mg = mg sin θ + μₛ mg cos θ.
  3. M = m(sin θ + μₛ cos θ) = 10(0.423 + 0.40 × 0.906) = 7.9 kg.

Answer key and printable worksheet

Open all answers
  1. It stays put (tan 15° = 0.27 is below 0.40).
  2. 20.3 N uphill
  3. 3.2 m/s² down the slope
  4. μₖ = tan 18° = 0.32
  5. 2.1 m
  6. Down the slope, 21.2 N
  7. 168 N
  8. 71 N
  9. 2.2 m/s²
  10. 7.9 kg

Studying for the final? Try the Physics 1 final exam review, a mixed practice test across the whole course.

Common questions

How do you solve inclined plane problems with friction?

Choose axes along and perpendicular to the fixed ramp. With no other applied force, N = mg cos θ. If the block starts at rest, compare mg sin θ with μₛN: static friction holds it when the required force is at or below that limit. If it is sliding, use μₖN and ΣF = ma along the ramp. Include any rope or push in the force balance.

What is the formula for acceleration on an incline with friction?

For a block sliding down with nothing else pushing on it, a = g(sin θ − μₖ cos θ), taking downhill as positive. A negative result means the block slows down. For a block sliding up, the size of the acceleration is g(sin θ + μₖ cos θ), pointing down the slope. These only work while the block is actually sliding.

Why is the normal force mg cos θ and not mg?

The ramp only has to hold up the part of the weight pressing into it, and that part is mg cos θ. A push or pull with a part perpendicular to the ramp changes N, so find it from the force equation rather than memorizing it.

Does mass matter on an incline with friction?

For a lone block on the same fixed ramp, with the same friction coefficients and starting motion, mass cancels from the acceleration and slip test. Mass still changes the forces. With a rope, pulley or applied force, include mass in the equations; whether it cancels depends on the setup.

When do I use static friction and when do I use kinetic friction?

Use μₛ to check the static-friction limit for a block that isn’t sliding; the actual friction may be smaller than μₛN. Use μₖ once it is sliding. If a problem gives you one coefficient and says the block slides, use that one with f = μN.

How do I find the coefficient of friction from an angle?

If a block slides at constant speed, μₖ = tan θ. If a block at rest just starts to slip as you tilt the ramp, μₛ = tan θ at that angle.

Keep practicing

Try 3 days free

3 days, unrestricted access. No card needed.

Want the energy route instead of forces? Try work-energy theorem practice, where friction’s work sets the final speed.

Sources and fact checks

Formulas and friction values were checked against these textbook references. Practice scenarios and worked numbers were written for this guide. All examples use the standard simple friction model, with no air drag.