PhysicsDrill

Rotation · 5 worked problems + 2 to try

Torque and rotational motion practice problems, solved step by step

Work each problem first, then open the solution. Every rotation problem uses the same moves as a linear one, with force swapped for torque, mass for moment of inertia, and v for ω. Take g = 9.8 m/s².

Problem 1 of 5

Problem 1: Torque on a wrench

You pull on the end of a 0.30 m wrench with 50 N of force, at 60° to the handle. What torque do you apply? What would it be if you pulled at 90°?

A wrench 0.30 meters long with a 50 newton force pulling on its end at a 60 degree angle to the handle. r = 0.30 mF = 50 Nθ = 60°pivot (bolt)
The angle θ is measured between the handle (the r direction, from the bolt to where you pull) and the force.
Given
r = 0.30 m, F = 50 N, θ = 60° (the angle between r and F)
Find
τ, then τ at 90°
Plan
τ = rF sin θ

Try it on paper first, then open the solution.

Show the solution to problem 1

Solve

  1. τ = (0.30 m)(50 N)(sin 60°) = (15 N·m)(0.866) = 13 N·m (12.99).
  2. At 90°, sin 90° = 1, so τ = (0.30)(50) = 15 N·m. That is the most torque this force can make at this distance.

Check

Pulling straight along the handle (θ = 0°) gives sin 0° = 0, so no torque. That makes sense: you can’t turn a bolt by pulling along the wrench. ✓

Tip: θ is the angle between the lever arm r and the force, not between the force and the floor. Another way to say it: τ = F × (lever arm), where the lever arm r sin θ is the perpendicular distance from the pivot to the force’s line of action. Here that is 0.30 × sin 60° = 0.26 m, and 50 N × 0.26 m gives the same 13 N·m.

Problem 2 of 5

Problem 2: Rotational equilibrium (beam on two supports)

A uniform 4.0 m beam with a mass of 20 kg rests on supports at both ends. A 60 kg person stands 1.0 m from the left end. Find the force from each support.

A 4.0 meter uniform beam resting on supports at each end, with a person standing 1.0 meter from the left end and the beam’s weight acting at its center, 2.0 meters from each end. person 588 N 196 N NL NR 1.0 m 2.0 m 2.0 m
Orange arrows are the two weights; blue arrows are the support forces. The beam’s own weight acts at its center.
Given
L = 4.0 m, mbeam = 20 kg (its weight acts at the center, 2.0 m from each end), mperson = 60 kg at 1.0 m from the left end
Find
NL and NR
Plan
Equilibrium means Στ = 0 and ΣF = 0. Take torques about the left support so NL drops out (it has zero lever arm there).

Try it on paper first, then open the solution.

Show the solution to problem 2

Solve

  1. Weights: beam = 20 × 9.8 = 196 N, person = 60 × 9.8 = 588 N, total = 784 N.
  2. Στ about the left end = 0, counterclockwise positive: NR(4.0) − 196(2.0) − 588(1.0) = 0, so 4.0 NR = 392 + 588 = 980 and NR = 245 N.
  3. ΣF = 0: NL = 784 − 245 = 539 N.

Check

Take torques about the right end instead: NL(4.0) = 196(2.0) + 588(3.0) = 392 + 1764 = 2156, so NL = 539 N. ✓ The left support carries more because the person stands closer to it.

Problem 3 of 5

Problem 3: τ = Iα with a spinning disk

A solid disk (a flywheel) has a mass of 2.0 kg and a radius of 0.25 m, and it spins freely on a fixed axle. Starting from rest, a 4.0 N force is applied tangentially at the rim for 3.0 s. Find (a) the angular acceleration, (b) the angular speed after 3.0 s, and (c) how many revolutions it turns.

Given
M = 2.0 kg, R = 0.25 m, F = 4.0 N tangent to the rim (θ = 90°), t = 3.0 s, ω0 = 0
Find
α, ω after 3.0 s, number of revolutions
Plan
I = ½MR² for a solid disk, then τ = Iα, then the constant-α kinematics equations

Try it on paper first, then open the solution.

Show the solution to problem 3

Solve

  1. I = ½(2.0)(0.25)² = ½(2.0)(0.0625) = 0.0625 kg·m².
  2. τ = RF = (0.25)(4.0) = 1.0 N·m.
  3. (a) α = τ / I = 1.0 / 0.0625 = 16 rad/s².
  4. (b) ω = ω0 + αt = 0 + 16(3.0) = 48 rad/s.
  5. (c) θ = ω0t + ½αt² = ½(16)(3.0)² = 72 rad, and 72 / 2π = 11.5 revolutions (11.46).

Check

The work done by the torque, W = τθ = (1.0)(72) = 72 J, should equal the rotational kinetic energy gained, ½Iω² = ½(0.0625)(48)² = ½(0.0625)(2304) = 72 J. ✓ (More on W = τθ and energy bookkeeping in the work-energy theorem practice guide.)

Try 3 days free

3 days, unrestricted access. No card needed.

Problem 4 of 5

Problem 4: Rolling down a ramp (rotational kinetic energy)

A solid sphere starts from rest and rolls without slipping down a ramp, dropping a height of 2.0 m. How fast is it moving at the bottom? Compare it with a block sliding down a frictionless ramp and with a hoop rolling down the same ramp.

Given
h = 2.0 m, solid sphere I = (2/5)MR², rolling without slipping so v = Rω
Find
v at the bottom
Plan
Energy conservation: Mgh = ½Mv² + ½Iω². Static friction does no work when there is no slipping.

Try it on paper first, then open the solution.

Show the solution to problem 4

Solve

  1. Rotational part: ½Iω² = ½(2/5)MR²(v/R)² = (1/5)Mv².
  2. Mgh = ½Mv² + (1/5)Mv² = (7/10)Mv², so v = √(10gh/7).
  3. v = √(10 × 9.8 × 2.0 / 7) = √28 = 5.3 m/s (5.29).

Compare:

  • Frictionless sliding block (no rotation): v = √(2gh) = √39.2 = 6.3 m/s.
  • Hoop (I = MR²): Mgh = ½Mv² + ½Mv², so v = √(gh) = √19.6 = 4.4 m/s.

Check

The more of an object’s mass that sits far from its axis, the bigger the share of the energy that goes into spinning, and the slower it rolls. Mass and radius cancel, so any solid sphere beats any hoop to the bottom. ✓

Problem 5 of 5

Problem 5: Angular momentum (the spinning skater)

A skater spins at 2.0 rev/s with her arms out (I = 4.0 kg·m²). She pulls her arms in, and her moment of inertia drops to 1.6 kg·m². Find her new spin rate and the change in kinetic energy.

Given
I1 = 4.0 kg·m², ω1 = 2.0 rev/s, I2 = 1.6 kg·m²
Find
ω2 and ΔKE
Plan
No outside torque about the spin axis (the ice is nearly frictionless), so L = Iω is conserved: I1ω1 = I2ω2.

Try it on paper first, then open the solution.

Show the solution to problem 5

Solve

  1. ω2 = I1ω1 / I2 = (4.0)(2.0) / 1.6 = 5.0 rev/s. Rev/s is fine here because the units cancel in the ratio.
  2. Energy needs rad/s: ω1 = 2.0 × 2π = 4π ≈ 12.6 rad/s and ω2 = 5.0 × 2π = 10π ≈ 31.4 rad/s.
  3. KE1 = ½(4.0)(4π)² = 32π² ≈ 316 J.
  4. KE2 = ½(1.6)(10π)² = 80π² ≈ 790 J, so ΔKE ≈ +474 J.

Check

KE2 / KE1 should equal I1 / I2 = 2.5, and 790 / 316 = 2.5. ✓ Angular momentum is conserved but kinetic energy is not: the extra ≈ 474 J comes from the work her muscles do pulling her arms in. It is the rotational twin of a collision where momentum is conserved but kinetic energy changes (see conservation of momentum practice problems).

Linear ↔ rotational cheat table

Every problem above was a linear problem in disguise. Swap each linear quantity for its rotational twin and the equations keep the same shape. Use radians in the arc length, speed, acceleration, and kinematics links. For sin θ, degrees work when your calculator is in degree mode.

Linear quantities and their rotational twins
LinearRotationalLink between them
position x (m)angle θ (rad)arc length s = rθ
velocity v (m/s)angular velocity ω (rad/s)v = rω
acceleration a (m/s²)angular acceleration α (rad/s²)atangential = rα
mass m (kg)moment of inertia I (kg·m²)I = Σmr²
force F (N)torque τ (N·m)τ = rF sin θ
ΣF = maΣτ = Iαsame shape
v = v0 + atω = ω0 + αtsame shape
x = v0t + ½at²θ = ω0t + ½αt²same shape
v² = v0² + 2aΔxω² = ω0² + 2αΔθsame shape
KE = ½mv²KE = ½Iω²rolling: both terms
p = mvL = Iωsame shape
W = Falong motionΔxW = τΔθfor constant force or torque

Common moments of inertia

Axis through the center unless noted.

  • Point mass at distance r: mr²
  • Hoop or thin ring: MR²
  • Solid disk or cylinder: ½MR²
  • Solid sphere: (2/5)MR²
  • Thin spherical shell: (2/3)MR²
  • Thin rod about its center: (1/12)ML²
  • Thin rod about one end: (1/3)ML²

The link v = rω is the same one you use for anything moving in a circle; see circular motion practice problems for the centripetal side, a = v²/r, which points toward the center instead of along the path like atangential = rα.

Try it yourself

Two problems that check your answer. Use g = 9.8 m/s². A wrong answer tells you the likely slip, and each problem has a hint and a full solution.

Interactive 1 of 2 · multiple choice

Seesaw balance. A 25 kg child sits 2.0 m from the pivot of a seesaw. Where must a 50 kg parent sit, on the other side, to balance it?

Show a hint for interactive 1

Balanced means the two torques about the pivot are equal: (weight × distance) on one side = (weight × distance) on the other.

Show the solution to interactive 1
  1. Torque from the child: (25)(9.8)(2.0) = 490 N·m.
  2. The parent must make the same torque: (50)(9.8)r₂ = 490 N·m.
  3. r₂ = 490 / 490 = 1.0 m. Or skip g: r₂ = (25)(2.0)/50 = 1.0 m.

Answer: B, 1.0 m from the pivot.

Interactive 2 of 2 · type a number

Door torque. Viewed from above, a 20 N horizontal force pushes on a door 0.50 m from the hinges. The force makes a 30° angle with the line from the hinges to where it pushes. What torque does it produce about the hinges?

N·m

Show a hint for interactive 2

The door itself is the r direction, so the angle between r and F is the 30° you were given. Only F sin 30° pushes the door around.

Show the solution to interactive 2
  1. r = 0.50 m, F = 20 N, θ = 30° (between the door and the force).
  2. τ = rF sin θ = (0.50)(20)(sin 30°) = (10)(0.5).

Answer: τ = 5.0 N·m. Answers within 2% (4.9 to 5.1) count.

Common mistakes

  • Using the wrong angle. θ in τ = rF sin θ is the angle between r and F. If you’re given the angle from the perpendicular, use cos instead, or convert first.
  • Leaving out the beam’s own weight. A uniform beam’s weight acts at its center. Include it in Στ.
  • Picking a bad pivot. In static equilibrium you can sum torques about any point. Pick the one where an unknown force acts, so that force drops out.
  • Plugging rev/s or degrees into energy or kinematics formulas. ½Iω², v = rω and a = rα need radians (1 rev = 2π rad). Rev/s is only safe in ratios like I₁ω₁ = I₂ω₂.
  • Using the wrong I. A solid disk is ½MR², not MR². And the same rod has a different I about its end, (1/3)ML², than about its center, (1/12)ML².
  • Assuming KE is conserved when L is. When a skater pulls in her arms, L stays the same but KE goes up. When a spinning object grabs onto another and they turn together, L is conserved but KE is lost.
  • Forgetting rotational KE in rolling. A rolling object has both ½mv² and ½Iω². Leaving out the second term gives the frictionless-slide answer, which is too fast.

FAQ

What is the formula for torque?

τ = rF sin θ, where r is the distance from the pivot to where the force acts, F is the force, and θ is the angle between r and F. The unit is the newton-meter (N·m). The same thing written another way is τ = F × (lever arm), where the lever arm r sin θ is the perpendicular distance from the pivot to the line of the force.

What does rotational equilibrium mean?

Zero net torque about an axis means angular momentum about that axis stays constant. For a rigid body whose moment of inertia does not change, its spin rate stays steady. For a fully static object the net force is also zero, and then the net torque is zero about every point, so you can pick whichever pivot makes the algebra easiest.

What is moment of inertia?

It is an object’s resistance to angular acceleration, the rotational version of mass. It depends on the mass and on how far that mass sits from the axis (I = Σmr²), so the same object has a different I about a different axis.

Why does a skater spin faster when she pulls her arms in?

With no outside torque about the spin axis, angular momentum L = Iω stays constant. Pulling the arms in lowers I, so ω has to go up. Kinetic energy is not conserved: it goes up, and the extra comes from the work her muscles do.

Where to go next

Keep practicing

Try 3 days free

3 days, unrestricted access. No card needed.

Sources and fact checks

The torque definition and lever arm, the conditions for static equilibrium, the moment-of-inertia formulas, τ = Iα, rotational kinematics, W = τθ and rotational kinetic energy, rolling without slipping, and conservation of angular momentum were checked against OpenStax University Physics Volume 1, chapters 10 to 12. The problems and numbers were written for this guide, and every answer was recomputed separately with g = 9.8 m/s².